TP.MSD309.BP85 Blaupunkt 39 / 210I-GB-5B-FHBKUP-EU  firmware dump.

Download Repair Firmware for Blaupunkt 39/210I-GB-5B-FHBKUP-EU TV – SPI Memory File for TP.MSD309.BP85

Television faults caused by corrupted firmware can render your TV inoperable, especially when the issue lies within the SPI flash memory. If you own a Blaupunkt 39/210I-GB-5B-FHBKUP-EU and you're facing issues such as no display, stuck on logo, or boot looping, the solution may lie in flashing a fresh SPI firmware file. In this post, we provide a reliable download for the repair firmware of the TP.MSD309.BP85 mainboard, compatible with the 25Q32 SPI chip.

Blaupunkt 39/210I-GB-5B-FHBKUP-EU TV Specifications

Here is a detailed table showing the technical characteristics of the affected TV model:

• Brand:      Blaupunkt

• Model:     39/210I-GB-5B-FHBKUP-EU

• Model Code: BB39L210BFBKPE995

• Chassis/Mainboard: TP.MSD309.BP85

• Screen Panel:     V390HJ1-LE1

• SPI Flash:              Winbond 25Q32

• File Format:         BIN

• Usage:  Flash via programmer to SPI IC

• Common Issues Fixed: Stuck on logo, black screen, no signal, boot loop

Why You May Need to Flash the SPI Firmware

Smart TVs rely heavily on firmware stored in SPI flash memory chips. When this data becomes corrupted—due to power surges, firmware update failures, or faulty software installations—the TV may stop functioning altogether. Common symptoms include:

• TV not powering on

• Logo freezing

• Black or blank screen

• Reboot loop

• No backlight despite power

By flashing a verified repair firmware directly to the SPI chip (25Q35 in this case), you can often restore functionality without the need to replace the mainboard.

Required Tools for Flashing

To successfully flash the firmware to your Blaupunkt TV, you’ll need the following tools:

1. SPI Flash Programmer – CH341A, TL866II Plus, or similar

2. SOIC8 Clip Adapter – for in-circuit programming

3. Computer (Windows preferred) – to run flashing software

4. Firmware File (BIN) – download provided below

Ensure you have basic knowledge of electronic handling and flashing procedures. If unsure, consult a technician.

Download the Firmware File

The firmware for the TP.MSD309.BP85 mainboard with 25Q32 SPI chip is available in BIN format, suitable for direct flashing. This dump file has been tested and is known to resolve common firmware-related issues on this model.

📥 [Download SPI Firmware – Blaupunkt 39/210I-GB-5B-FHBKUP-EU]
(Direct BIN file – for TP.MSD309.BP85 mainboard, 25Q32 SPI)

💾 File Size: ~4MB
📁 Format: .BIN
🔐 Password: None

Note: Always back up your existing SPI firmware before flashing.

How to Flash the Firmware (Basic Steps)

1. Disconnect TV from power completely.

2. Connect SOIC8 clip to the SPI chip (25Q32).

3. Connect programmer to PC and launch flashing software.

4. Read and save the original dump (optional but recommended).

5. Load the new BIN file and write it to the chip.

6. Verify the written data and disconnect the programmer.

7. Reconnect TV and power on.

⚠️ Disclaimer: Proceed at your own risk. Improper flashing may result in hardware damage. This guide is intended for educational and repair purposes only.

Additional Tips & Troubleshooting

• If your TV shows no improvement, recheck the soldering or clip connection.

• Try using a different programmer or a known-good SPI dump.

• Ensure your power supply and inverter board are working before assuming firmware fault.

• For persistent problems, consider testing another mainboard with the same specs.

Conclusion

Corrupted SPI firmware can cripple even a high-quality TV like the Blaupunkt 39/210I-GB-5B-FHBKUP-EU. However, by flashing the correct dump file for the TP.MSD309.BP85 board and 25Q32 SPI chip, you can often restore full functionality. This solution is effective for many common faults including black screen, stuck logo, and no signal issues.