MBSPI1506CM01-dsz-v1.2.pcb

DOWNLOAD MBSPI1506CM01-dsz-v1.2.pcb Firmware Dump for GOLRAY MINI HD4.

Title: Download GOLRAY MINI HD4 DVBS2 Repair Firmware Dump (MBSPI1506CM01-dsz-v1.2, EN25Q32) – Free SPI Flash Recovery

Is your  GOLRAY MINI HD4 DVBS2  receiver stuck on boot or bricked after a failed firmware update? Don’t worry—this guide provides a free SPI flash memory firmware dump tested and verified by reflashing. The firmware dump is compatible with the MBSPI1506CM01-dsz-v1.2.pcb mainboard, and is intended for recovery using SPI programmers such as the Sofi SPI_8A.

This article includes a detailed breakdown of hardware specifications, firmware information, and step-by-step guidance for recovery—ideal for technicians and enthusiasts restoring non-working satellite receivers.

Device Overview: GOLRAY MINI HD4 DVBS2

The GOLRAY MINI HD4 is a compact yet powerful **DVB-S2 satellite receiver** known for its affordable price and decent hardware. Here are its key characteristics:

- Brand:  GOLRAY  

- Model: MINI HD4  

- Device Category:  DVB-S2 Satellite Receiver  

- Form Factor: Mini Set-top Box  

- Purpose:  Free-to-air satellite channel reception  

- Bootloader Type: MBSPI1506 compatible  

 Technical Specifications

Below are the important technical components found inside the MINI HD4 receiver:

- Main Board:  MBSPI1506CM01-dsz-v1.2.pcb  

- CPU/MCU:  MBSPI1506 (ALI-based processor)  

- Flash Memory:  EN25Q32 (32Mbit SPI NOR Flash)  

- Firmware Size: 4.19 MB  

- Dump Type: Full SPI Flash binary (.bin format)  

- Tested With Programmer: Sofi SPI_8A  

-Firmware Source:  Personally dumped and tested through successful reflashing  

Why You Might Need This Firmware Dump

If you’re facing any of the following issues with your GOLRAY MINI HD4 DVBS2, reflashing the SPI memory with this dump may help:

- Device stuck on boot logo  

- Remote control not working  

- No signal or channels lost  

- Bricked after OTA update  

- No display or frozen interface  

This firmware dump provides a clean, working flash state for the EN25Q32 memory, helping to restore the receiver to factory condition.

How to Use the Firmware Dump

Step 1: Required Tools

- SPI Programmer: Sofi SPI_8A, CH341A, RT809H or similar  

- Software: Sofi Tool, NeoProgrammer, or SPI Flash utility depending on your programmer  

- Clip Adapter: SOP8 test clip for in-circuit programming (if you do not desolder)

Step 2: Backup Existing Flash

Before writing the new firmware, always read and save the original contents of the EN25Q32 chip, in case you need to revert.

Step 3: Write the Dump

- Load the downloaded `.bin` firmware into the programmer software  

- Erase the chip and perform a blank check  

- Write the firmware and verify  

- Reassemble the receiver and test for proper operation  

Download the Firmware Dump (Free)

You can download the working firmware dump for the GOLRAY MINI HD4 DVBS2 receiver via the link below. It’s free to use for personal or repair purposes.

📥[Download GOLRAY MINI HD4 Firmware Dump – 4.19 MB]  

Tested & Verified – Format: BIN

⚠️ Important: Always verify your board version before using the dump. This file is for  MBSPI1506CM01-dsz-v1.2 only.

Disclaimer

This firmware dump is provided as-is, without any warranty. It has been successfully tested, but using it is at your own risk. Flashing memory chips incorrectly can lead to permanent damage. Always double-check your board version and use a verified programmer.

Final Thoughts

Restoring a dead or bricked  GOLRAY MINI HD4 DVBS2  satellite receiver is entirely possible using the right tools and a clean SPI firmware dump. This recovery solution is ideal for technicians working with digital satellite equipment. Whether you’re repairing for a client or restoring your own device, this dump can save both time and money.